Description
Overview
Moisture probe for mapping the migration of water through carpet and underlay. The HydroSensor I has a 790 mm (31 inch) reach, so you survey a room standing up rather than on your knees.
Nickel-plated points signal moisture content above 17 per cent. For carpet and underlay only — it is not intended for timber, plaster or masonry.
At a Glance
The original — map the migration of water in the carpet and pad without straining your back.
- The HydroSensor I has a 31-inch reach to save your knees and back.
- Sensitive nickel-plated points alert you to moisture content above 17%.
- Use only on carpet and pad.
How it differs from the HydroSensor II
The HydroSensor II (F251) has a collapsible shaft that extends to 790 mm for use and folds to 530 mm for storage. This one is fixed length.
If the probe lives in a van or a kit box, the collapsible shaft is the reason to pay the difference. If it lives on a truck and gets used all day, a fixed shaft has less to go wrong.
Reading it
The light flashes and the transducer beeps when moisture is present, and the rate increases with the moisture content, so you map the wet edge by working outward until the signal stops.
It will also respond to urine residues in carpet and underlay, because urine salts hold enough moisture to register. A black light is the way to confirm urine is actually present rather than assuming it from the probe alone.
Using It
- Extend the sensor points: loosen the black plastic knob, push it down and around the S-shaped slot, then tighten it to lock the points in position.
- Test the unit by placing your fingers across the points. The indicator lamp lights and the unit beeps.
- Probe the suspected wet area. Flashing and beeping means the carpet and/or underlay is wet; a faster rate means more moisture.
- Do not force the probe. Excess force can damage the tips.
- Retract the points into the shaft whenever the probe is not in use.
Safety: the sensor points are extremely sharp. Always retract them before carrying or storing the probe.
Carpet and Underlay, or Other Materials?
Dri-Eaz's owner's manual says that, with care, the HydroSensor can also be used to find moisture in furniture, walls and ceiling materials. Dri-Eaz's current product page says it is for use on carpet and pad only, and we recommend the same.
The reason is what the probe measures. It is a wet/dry indicator with a single alarm point (moisture content above 17 per cent), not a moisture meter that gives a reading you can record and compare. For timber, plasterboard and masonry, and for any reading that goes into a drying log or insurance report, use a moisture meter such as the Delmhorst BDX-20.
Specifications
| Brand | Dri-Eaz (Legend Brands) |
| Model | HydroSensor I (F245) |
| Length | 31 in. (787 mm), fixed shaft |
| Probe tips | 7/8 in. (22 mm) nickel-plated steel, retractable |
| Alarm point | Moisture content above 17% |
| Indication | LED in the handle and audible beep; rate increases with moisture |
| Shaft | Stainless steel |
| Handle | Injection moulded |
| Power | One 9 V battery (included) |
| Weight | 1 lb (about 0.45 kg) |
| Warranty | Legend Brands limited warranty — 1 year parts and labour (see below) |
Length and weight are from the Dri-Eaz owner's manual. The alarm point is from Dri-Eaz's product page.
Care, Tips and Battery
- After each use, clean and dry the probe with a soft cloth.
- If the probe tips become dull, they can be resharpened with a file. If they are worn out, a replacement point set is available from Dri-Eaz (part 12-00085) — it is not listed online, so ask us.
- The probe runs on one general-purpose 9 V battery inside the handle, below the indicator light. If the light no longer comes on, remove the small screws holding the handle halves together, split the handle gently, fit a new battery, and refit the screws without pinching the wires or overtightening.
- Battery life depends on use and storage. Do not leave the tips in contact with metal, damp cloth, carpet, water, cork or anything else that conducts electricity — the probe will keep drawing current.
Warranty
Legend Brands' limited warranty for Dri-Eaz moisture instruments covers the original purchaser for one year from the date of purchase on parts and labour, for products bought from an authorised distributor. Consumable and wear items, including batteries, are excluded. The full terms are in the warranty document below; talk to us first if you have a problem with your probe.
Frequently Asked Questions
Does it give a moisture percentage?
No. It alarms when moisture content is above 17 per cent, and the flash and beep rate increases with moisture. Use it to find and map the wet edge, then use a moisture meter for recorded readings.
Should I buy this or the HydroSensor II?
The HydroSensor I has a fixed 31 in. shaft. The HydroSensor II extends to the same working length but folds to 21 in. (533 mm) for storage. Buy the II if the probe travels in a kit box.
Can it find urine in carpet?
It responds to urine residues because urine salts hold enough moisture to register. Confirm with a black light, such as the SOS UV Black Light Kit, before quoting urine treatment.
What battery does it take?
One general-purpose 9 V battery, fitted inside the handle. One is included.
The light has stopped working — is it faulty?
Check the battery first. Test by placing your fingers across the points: if the lamp does not light with a fresh battery, contact us with the model number from the product label.
Documents
- Owner’s Manual — HydroSensor I & II, models F245 and F251. Document 07-00315 Rev. F.
- Parts Breakdown — covers F245, F245-SM, F245-SP, F251, F251-SM and F251-SP.
- Limited Warranty — Dri-Eaz moisture instruments, Legend Brands.
Parts and service
The parts breakdown above covers the F245 and F251 in all variants. If you are unsure which meter you have, the model number is on the product label — send it to us and we will confirm the right part before anything is ordered.
- Point set assembly (Dri-Eaz part 12-00085) — ask us
Related Products
Not sure whether the fixed or collapsible shaft suits how you work? Ask us — we list both.
Estimate shipping
Refund Policy
Refund Policy
At The Moisture Meter Company (TMMC), a division of Carpet Cleaners Warehouse, we are committed to complying with the Australian Consumer Law (ACL) and providing fair outcomes for our customers.
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement, repair, or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure.
Damaged, Faulty or Incorrect Goods
If you receive a product that is damaged in transit, faulty, defective, or incorrectly supplied, please contact us as soon as possible.
To assist with assessment, we may request photographs, serial numbers, proof of purchase, or other information relevant to the claim.
Where a product is confirmed to be faulty, damaged, incorrectly supplied, or otherwise covered under Australian Consumer Law, TMMC will provide an appropriate remedy, which may include:
- Repair
- Replacement
- Store credit
- Refund
TMMC will cover reasonable return shipping costs for approved warranty, fault, damage, or incorrect supply claims.
Change of Mind Returns
TMMC may, at its sole discretion, accept returns for change of mind within 14 days of delivery, provided that:
- The return is approved by TMMC before being sent back.
- The product is unused and in original condition.
- The product is returned in its original packaging.
- All accessories, manuals, and included items are returned.
- The product is not a special order, made-to-order, clearance, consumable, or non-returnable item.
Approved change of mind returns may be subject to a restocking fee and the customer is responsible for all return shipping costs.
Original freight charges are non-refundable unless required under Australian Consumer Law.
Non-Returnable Items
Unless required under Australian Consumer Law, the following items cannot be returned for change of mind:
- Special order products
- Made-to-order products
- Hygiena swabs, test reagents and other consumables
- Probes, electrodes and pins that have been used
- Products specifically marked as non-returnable
- Clearance or end-of-line items
Return Process
Before returning any product, customers must obtain return authorisation from TMMC.
Please contact us using one of the methods below:
- Phone: 1800 68 68 69
- Email: info@moisturemeters.com.au
Returns sent without prior approval may be refused or delayed.
Refund Processing
Approved refunds will be processed to the original payment method used for the purchase unless otherwise agreed.
Refunds are generally processed after the returned product has been received, inspected, and approved.
Processing times may vary depending on the payment provider.
Warranty Claims
Many products sold by TMMC are also covered by manufacturer warranties. These are in addition to your rights under the Australian Consumer Law.
Warranty claims may require inspection, testing, repair, replacement, or manufacturer assessment before a final outcome is determined.
Equipment must be returned to TMMC in Queensland for warranty assessment. The customer pays freight to return the item; if a covered fault is confirmed, TMMC reimburses that freight and pays return freight. If the fault is not covered, we will provide a written quote before any work is done.
Business Customers
Nothing in this policy excludes, restricts, or modifies any rights available under Australian Consumer Law.
Where permitted by law, remedies available for goods supplied for business use may be limited in accordance with applicable legislation.
Contact Us
The Moisture Meter Company
Phone: 1800 68 68 69
Email: info@moisturemeters.com.au
Queensland
D1-3/194 Zillmere Road, Boondall QLD 4034
Victoria
Unit 1/5 Gatwick Road, Bayswater North VIC 3153
This policy was last updated on 18 November 2026.

